Skip to content

National Restoration Parts

Car Restoration tips, news, installs, parts and more

Menu
Menu

How to choose the correct stall speed for your converter

Posted on November 29, 2010

A normal converter has a stall, depending on vehicle, from 900 to 1,200 RPM. As the stall speed increases, the lockup increases, but with normal driving the vehicle will accelerate with small load fairly normally as long as the stall does not exceed 3,000. When max power is called for, the stall will flash to the stall speed before lockup occurs. If a vehicle is doing 30 mph at 1,500 RPM in second gear, when floored, the RPM will flash to 3,000 before beginning to pull hard. The pros and cons to this are important considerations. When the stall flashes, it will throw the engine into the power band and pull much harder than a conventional converter. The con is that, with the stock converter, top speed in second may be 50 mph at 5,500 RPM, and with the stall converter it will be around 7,200 at the same speed. The shift points will have to be considered as to speed to stay within RPM limits.

A stall converter is a necessity in racing to get to max torque as fast as possible. For hauling, such as getting a heavy boat out of the water, a stall of 2,500 max is recommended. Anything higher would create driving problems while hauling, and will kill the fuel economy. Don’t forget that going down the road every time the foot is lifted off the gas, or when the vehicle is cruising and a small increase in speed is desired, the RPM will jump to 2,500. In this case, before it will accelerate and when the speed is reached, the RPM will drop lower while cruising. It is almost like the transmission is slipping until the stall is reached.
The proper use of a stall converter for racing is to stage the car and hold the brake pedal just prior to launching, and flash the engine to the stall before releasing the brake. Do not flash the stall in the first staging lights. As you set of the first set of lights, ease the RPM up close to flash, bump-brake the car into the final staged lights, then immediately flash and hold. Flashing early heats up the converter and the transmission fluid if held too long.

Converter Stall Combinations
A vehicle which weighs around 2,800 lbs. with a highway gear of no lower than 2.70 and a 4-speed overdrive that does around 2,000 RPM at 60 with no more than 180 bhp, uses a 2,500 RPM stall converter.
The same situation as above, but with a modified engine with 240 bhp or better and an RPM limit of 7,500, uses a 3,500 stall to get into the preferred RPM band quickly. Use a wider, stickier tire.
A vehicle weighing 3,600 to 3,800 lbs. with a highway gear and an overdrive and 240 to 350 bhp and 300 foot-pounds of torque uses a 3,500 stall. This will produce the best ET for the hp rating.
Same weight class, lower gear such as 3.73 to 4.11, horsepower rating of 375 to 450 with 420 plus torque rating, uses a 3,000 street or strip or 3,800 strip stall speed.
Same weight, low gear 3.73 to 4.11, horsepower rating 500 to 685 with 550 plus torque, uses a 2,500 to 2,800 stall. This will give a much better controllable 60 foot time without just spinning the tires with this much torque. With the right rubber, this can give a 1.2 or better 60 foot.
A 3,000 lbs. car with a modified suspension (4-link rear with 4.11 to 4.56 or lower gear), a modified 200R transmission and a modified engine with overhead cams, or using stud girdles on a conventional cam with a large turbo putting out in excess of 850 horsepower and about the same in torque, uses a 4,000 to 4,500 stall. For a super charger, use 1,500 to 2,200 stall speed.

Advertisements

Recent Posts

  • Buy a Classic Car or Build One?
  • Having trouble finding Classic Car parts? Here’s why..
  • How to find a hidden gem of a Classic Car
  • What’s the difference between R12 and 134a Air Conditioning Systems
  • Modern Muscle how to add Horsepower

Categories

  • Body Parts
  • Engine
  • Interior
  • Restoration
  • Suspension
  • Uncategorized

Recent Comments

  1. wayne wheatcraft on Where to buy vintage restoration parts

    looking for a rear defroster unit for a 1973 RS Camaro

  2. Doug Hood on Which type of Quarter Panel repair do you need?

    1968 Mercury Cougar part quarter panels

  3. Dave Wilks on Buy a new classic car body shell to restore?

    I need a complete 1971 mustang convertible body shell

  4. Vanessa on Buy a new classic car body shell to restore?

    55 nomad I need full floor to trunk rockers inner outer ext on and on 818-562-0974

©2023 National Restoration Parts | Design: Newspaperly WordPress Theme